清理沸石转轮堵塞的方法主要包括以下几种：

　　The methods for clearing blockages in zeolite wheels mainly include the following:

　　毛刷清理 ：

　　Brush cleaning:

　　使用直径在0.3 ~0.5 mm 的尼龙丝束垂直刺入转轮表面，破坏堵塞物与转轮孔壁的黏结，使堵塞物脱离转轮且不伤害转轮结构。为提率，可以将平面毛刷改造为滚筒型，并配备手柄，通过滚动动作清理转轮表面。

　　Use nylon fiber bundles with a diameter of 0.3~0.5 mm to vertically pierce the surface of the wheel, breaking the adhesion between the blockage and the wheel hole wall, allowing the blockage to detach from the wheel without damaging the wheel structure. To improve efficiency, the flat brush can be transformed into a drum type and equipped with a handle to clean the surface of the wheel through rolling action.

　　压缩空气吹扫 ：

　　Compressed air blowing:

　　使用日常使用的压缩空气（压力为0.8 MPa）对转轮进行吹扫，虽然可以吹出少量堵塞物，但效果不佳。因此，通常需要结合其他方法使用。

　　Using daily compressed air (with a maximum pressure of 0.8 MPa) to blow the impeller, although it can blow out a small amount of blockage, the effect is not good. Therefore, it is usually necessary to combine other methods for use.

　　毛刷和压缩空气结合 ：

　　Combination of brush and compressed air:

　　步骤一 ：用毛刷对转轮表面进行滚刷，直到将堵塞物与转轮的黏连状态打破，注意不要使用毛刷在转轮横向摩擦，以免损坏转轮。

　　Step 1: Use a brush to roll the surface of the wheel until the adhesion between the blockage and the wheel is broken. Be careful not to use the brush to rub laterally on the wheel to avoid damaging it.

　　步骤二 ：用压缩空气从反方向对转轮进行吹扫，压缩空气压力根据转轮实际耐受力设定，原则上在不损坏转轮的前提下越大越好。

　　Step 2: Blow the rotor in the opposite direction with compressed air. The compressed air pressure is set according to the actual tolerance of the rotor, and in principle, the larger the pressure, the better without damaging the rotor.

　　步骤三 ：对过滤箱和转轮前后进行深度清洁，避免清理出的堵塞物再次进入转轮。这种方法可以取得良好的效果，使转轮压差从2000 Pa 降为800 Pa 左右，转轮效率提升98%。

　　Step 3: Thoroughly clean the filter box and the front and rear of the impeller to prevent any blockages from entering the impeller again. This method can achieve good results, reducing the pressure difference of the impeller from 2000 Pa to around 800 Pa and increasing the impeller efficiency to 98%.

　　建议根据具体情况选择合适的清理方法，并严格按照步骤操作，以确保转轮的运行和延长使用寿命。

　　It is recommended to choose the appropriate cleaning method according to the specific situation and strictly follow the steps to ensure the efficient operation of the wheel and extend its service life.

　　本文由沸石转轮＋CO提供技术支持，更多的详细精彩内容请点击我们的网站//www.cdzjbccc.com，我们将会全心全意为您提供满意的服务。

　　This article is supported by zeolite wheel and CO technology. For more detailed and exciting content, please click on our website //www.cdzjbccc.com We will wholeheartedly provide you with satisfactory service.